Installing win2k from DOS

Recently acquired a windows 2k cd from my dad (he got it through some deal but doesn't want it, win98 is too complicated for him as it is) So I figuired I'd run it. I want to wipe out my me install and start fresh, this says it's the full version + upgrade. I slap in my 98 boot disk and just tell the computer to load with cdrom support. Get to dos prompt and try launching setup.exe from the cdrom.

"This program cannot be run from dos"

Baru?


Any work around for this or am I going to have to install ME on my secondary drive just to intall 2k on the main drive?


------------------
A Winner Is You

it be best to copy all the 2k setup files to your hard drive first. create a dir under your c drive and then copy all the file and dirs under the i386 dir on the 2k cd, and then run WINNT from within your hard drive i386 dir. remember to remove the 98 boot disk.

INstead of booting off the win98 startup, Boot off the windows 2000 cd itself. This can be done in the bios. You should have no problems from tehre

------------------
My Rig

Quote:

---

Originally posted by krazie662:
INstead of booting off the win98 startup, Boot off the windows 2000 cd itself. This can be done in the bios. You should have no problems from tehre

---

Tried that, for some odd reason it won't boot. Checked the bios, it's set to boot off my cdrw drive, put the cd and it just loads windows like normal.


Confused


------------------
A Winner Is You

my friends copy of win2k wont boot off the cd eather but my copy will...werid huh?

------------------
CPU: AMD 1.4 266
Heatsink w/fan: swifttech m462
Motherboard: ASUS A7M266
Ram: 2 MICRON 256MB DDR Ram PC2100 Cas Latency 2
Sound Card: Hercules Game Theater XP
Klipsch Promedia 5.1 :D woot woot
NIC: 3COM 905CX-TXNM Etherlink 10/100mbps PCI
IDE Controller: Promise Ultra100TX2
Video Card: Elsa GeForce2 ULTRA with Thermaltake blue orb fan/heatsink
CD-RW: Plextor 16/10/40A
Floppy drive: Sony
Hard drive: Western Digital 40gig 7200 rpm
4 ATA100 Rounded IDE cables
1 Floppy Rounded IDE cable
Case: custom with 2 fans on the side, 3 in case
2 Removable hard drive bays
Power supple: Enermax EG-465P-VE (450 watt)
Enermax Dual Temp Monitor rack

Server computer specs will be here soon :)

Assuming it's a genuine Microsoft CD...

Step 1: Get yourself four blank 1.44 MB floppy disks.

Step 2: Boot to your Win98 boot disk with CD support.

Step 3: From the command prompt, run X:\BOOTDISK\MAKEBOOT.EXE (where X: is the drive letter of your CD-ROM drive). This will make the Windows 2000 setup floppy set.

Step 4: Insert Disk 1 of the set you just made and reboot the system. Follow the instructions on the screen, and Windows 2000 installation will start.

I had the same problem until I made the 32-bit version boot disks. Same steps as SkyDog mentioned except use:

makebt32.exe

instead of makeboot.exe.

Quote:

---

Originally posted by delts:
I had the same problem until I made the 32-bit version boot disks. Same steps as SkyDog mentioned except use:

makebt32.exe

instead of makeboot.exe.

---

Use MAKEBOOT.EXE if your running the program from a DOS or Windows 9x boot floppy command prompt. Use MAKEBT32.EXE if you're running the program from within Windows.

I had the sam problem. I made the boot disks in Windows 98 off of the Win 2K CD. All you have to do is navigate to makeboot.exe on the CD and click on it. Just Follow the instructions. My CD wouldn't boot either so I had to follow these steps. It takes four floppies.

------------------
Enlight 7237 300 Watts
Abit KT7A
T-Bird 1.2 /226 FSB (@ 9.5 x 10=1266 for now)
Elsa Gladiac Geforce 2 GTS 32 MB DDR 212/368
512 MB PC 133 Cas 2 Micron SDRAM
Sony 12x8x32 CD-RW
Delta DVD 12x
IBM 40.2 Gig UDMA 100 7200
Stuck with Diamond 56K Modem
Generic 10/100 NIC
Viewsonic GS790 @ 1280x1024x32
----------------------

You gotta love the smell of Methanol in the mornin'