I am having major install probs with KT7A-Raid
Help!!! I just got a new KT7A-Raid and have been dragged to hell and back by it. Here is my setup
Win98SE
900mhz TB with unlocked L1 bridges but no OCing yet.
KT7A-RAID
128MB CL2 Crucial mem.
20gig Maxtor 7200/UMDA66 HD (Tried it first on IDE 3 as master, the first raid plug on the mobo. Now it is running off of IDE 1 as master.)
Tobisha DVD on IDE 2 (master)
NEC Floppy
NDC 10/100 Ethernet card
*ATI Radeon 32mb DDR
*Diamond MX300
*=problem inducing (I think...)
Alright, here is what's up. When I install the Ati drivers (I have tried using the ones off to the cd {v100} and the ones off of the 'net v4.13.7072 for sure and maybe the v4.12.3056 one {I have it too but cannot remember whether or not I have installed it in the multiple installs I have done}) I find that occasionally when I get to the flying windows part of the startup I am treated to a screen that tells me that it is now safe to shut down my computer. I found the following on via's site:
Quote:
From Via's FAQ
http://www.viatech.com/support/faq.htm:
Win98 Installation
Q: What is the procedure for installing Win98 on VIA chipset based systems?
A: There are four important steps to follow:
1) Go into BIOS setup and enable USB
2) Install Win98 on your system
3) Download and install the VIA IrQ routing miniport driver from our driver page
4) Download and install the VIA AGP driver from our driver page (for MVP3 & VP3 chipsets only)
Do I have a MVP3 or VP3 chipset; should I do step #4? Should I for-go the 4-in-1 drivers altogether (I have v425a installed)?
At http://www.apushardware.com/faqs/kt7faq/kt7faq.htm, Pauls Unofficial KT7 FAQ it mentions a fix for an unstable Radeon card:
Quote:
From Paul's Graphic's Card FAQ:
My ATI Radeon DDR graphics card is unstable. How can I fix it?
You have to use the 3054 or 3056 driver set with this board. There is also a sequence you need to follow in loading the board drivers and VIA's AGP driver. This driver needs to come from the 4.23 or 4.24 driver set. If you use WindowsMe you do not have to worry about DirectX installation either. Go to www.rage3d.com and review the forums for further help.
For the KT7 use the following sequence, if you load WindowsMe skip the DirectX step.
Fully remove the previous ATI driver set using uninstall.
Choose PCI Adapter and reboot.
Load DirectX 7.0a.- reboot
Load latest VIA AGP driver - reboot
Load ATI driver set 3054 or 3056 for Win98/Me - reboot
Reload latest VIA AGP driver from 4.24 set - reboot
Load DirectX 7.0a- reboot
Depending upon the system setup, steps 5 and 6 may not be needed.
You may need to set the AGP driving strength to 68.
If you have difficulty running at AGPx4 ABIT recommend you download the latest drivers from: http://support.atitech.ca/drivers/wi...6_directx.html http://www.3dchipset.com/drivers/ati...063/win9x.html
Do you think that I can use ATI drive 3056, substitute VIA AGP driver 4.24 for version 4.25a, and substitute DirectX 7.0a for version 8 and still get the same results?
Does it matter that I am using the Standard Display Adapter (VGA) instead of the mentioned "PCI Adapter"?
I know this is long, thank you for getting this far in the post. Right now I am running without the MX300 and using the Standard Display Adapter (VGA) with DX8 and everything is stable. I never went into BIOS setup and enabled USB (part 1 of Via FAQ above) before installing, could this be part of my problems? What should I do?
Thanks
Azk
------------------
Athlon 900 TB
on a KT7A-RAID
128MB PC133 CL2
ATI Radeon 32MB DDR
KDS VS-190 19"
MS IntelliMouse Explorer
[This message has been edited by Azk (edited February 03, 2001).]
