Search Results - Sharky Forums

Sharky Forums


Search:

Type: Posts; User: kenrippy

Search: Search took 0.70 seconds.

  1. Replies
    98
    Views
    537,128

    hey remember this thread? :D lol thought I'd...

    hey remember this thread? :D lol

    thought I'd resurrect this dinosaur of a thread for the fact it might help someone. it's got some good info in it.
  2. Replies
    98
    Views
    537,128

    here's the deal with that....the pump (most of...

    here's the deal with that....the pump (most of them) run on 110v AC. most people just make a small hole to run the pump cord out the back of their case. then have it plugged into a power strip...
  3. Replies
    98
    Views
    537,128

    hey speed freak, The one thing I see that...

    hey speed freak,

    The one thing I see that needs some change is the rad air flow should be sucking fresh air in. not having case air going thru your rad. and it might get a bit warmer up near...
  4. Replies
    98
    Views
    537,128

    from what everyone says, Eheim is the standard by...

    from what everyone says, Eheim is the standard by which every other brand of pump is measured. reliability, noise, heat etc. but reliability being the most important.
  5. Replies
    98
    Views
    537,128

    i don't see any maintenance either way. it's...

    i don't see any maintenance either way. it's just harder to get all the bubbles out with the "t" setup. figure the water jetting by the "t" and some of the bubbles won't make it up the t-line...
  6. Replies
    98
    Views
    537,128

    T line

    this pic is of a "T" line added to a system that doesn't have a res. this is used for a bleed/air gap instead of a res. the purpose of this is so the air will be trapped in the top of the T where...
  7. Replies
    98
    Views
    537,128

    the water line on that res pictured above would...

    the water line on that res pictured above would be over the top of both tubes. (see my pics) it's just that the much smaller intake tube would allow any air bubbles to not be sucked back into the...
  8. Replies
    98
    Views
    537,128

    hey guys, sorry i've been out of town for a few...

    hey guys, sorry i've been out of town for a few days.

    regarding the Innovatek "Tank-O-Matic" reservoir and 1/2" tubing. I've seen it done before by using it without the retainer nuts that tighten...
  9. Replies
    98
    Views
    537,128

    pyro, you should just make a webpage or...

    pyro, you should just make a webpage or something. and build a damn w/c rig why don't you....so we can call you "hydro" instead of pyro. j/k :p
  10. Replies
    98
    Views
    537,128

    http://www.hwtec.de/Seite.htm here's a good...

    http://www.hwtec.de/Seite.htm here's a good page to see what's out there on the w/c market.
  11. Replies
    98
    Views
    537,128

    the main diff between my setup and most others,...

    the main diff between my setup and most others, is the lines are 3/8" OD and the blocks are a low flow design which are designed for smaller diameter tubing. I personally don't like 1/2" ID tubing...
  12. Replies
    98
    Views
    537,128

    I chose to go with Purple Ice...

    I chose to go with Purple Ice added to distilled water.

    edit: btw Pyro, what hardware do you have in your w/c setup? you speak as if you have quite a bit of experience in this area.
  13. Replies
    98
    Views
    537,128

    ick. i've seen that at fry's. they sell the...

    ick. i've seen that at fry's. they sell the kit, think it's swiftech. it's aluminum and SUPER thin and cheezy looking in person! stay away from that one IMO.
  14. Replies
    98
    Views
    537,128

    the BIX is supposed to be the best "pc" rad on...

    the BIX is supposed to be the best "pc" rad on the market. some will say the heater cores are better but they can be huge and sometimes require 2 x 120mm fans.
  15. Replies
    98
    Views
    537,128

    i was able to get great cooling with a low flow...

    i was able to get great cooling with a low flow setup so you don't need the hugest gph pump to have the best cooling. see my sig link for the complete list of parts. it's just an option for ya,...
Results 1 to 15 of 15