Remember my RAM cooling mod?

Well, I'm back at it and I cut up a stock P4 heatsink and mounted it on my Raddy 9700. Some step by step instructions for anyone wanting to do this:

• First you gotta measure your heatsink to see how much you need to cut. On the other hand, you could just buy a heatsink that doesn't get in the way of anything on the board.
  
• Cut the thing down. I used a hacksaw and to tell you the truth, it was not easy. Took me ~1 hour of pure cutting (the breaks I took, cause my arm was aching, are not included in this time) to cut it to the right size. Cutting it too big the first time did not help. :p
  
• Then wrap the bottom on the heatsink in masking tape. Place it over your core and line it up whatever way you want to. Keeping the heatsink pressed against the core, turn it upside down and push a pencil through the mounting hole on the back of the card and mark only one hole. Go ahead and drill the hole. I used a high speed drill bit and it was no prob.
  
• Now find some 4/40" nuts and bolts that are about 3/4 to 1" long. The 1/2" I got were too short so I had to go out and get some 1" ones. You'll also need either rubber or plastic washers to prevent shorting out anything on the card.
  
• Put it through the heatsink and then through the mounting hole on the card. place the washer on the back of the card and tighten the nut on the back. Once you've got it fairly secure, mark where the second hole will be. This way, it'll be sure to fit perfectly. (I did this but my drilling technique leaves something to be desired so it was crooked anyways)
  
• Go and drill the second hole.
  
• Now I lapped the bottom of the heatsink with first 220 grit, (to get all the crappy drill marks off) then 600 grit, then 1500 grit finally.
  
• Apply ASIII or whatever you're gonna use to both the heatsink and core.
  
• Now, there are 2 ways you can secure the heatsink. First, you can just screw it in and tighten it til it's good and tight. But I was scared of crushing the core so I decided to use the springs from the push pins to provide some safety. Just place it around the bolt , put it through the heatsink and card, place the washer on the other side and tighten the nut til it can't anymore. That way, the spring's taking some of the pressure so not all of it's transfered to the core in case you overtighten.
  
• Tighten both sides until you're nice and secure.
  
• Slap a fan on top and you're ready to roll!

This was basically free for me since I had most of the materials (except the nuts and bolts which costed me all of ~$2.50) and yeilded quite an improvement. The back of the GPU used to be extremely hot to touch after playing some games even at stock speeds. Now when o/ced it's only warm. Before I could only go artifact free to ~375MHz and this morning I just tested it to 392MHz with no probs at all. Hopefully I'll be able to reach 400MHz.:D

Expect some new 3DMark scores from me soon..:D

BTW, I'll get some pics up later tonight as I don't have the digital camera here. So yeah, you can see my ugly, ugly work.;) :p

Very nice; looking forward to pictures.

Yeah, I'm curious to see the pic as well.

Yep, I'll get them up as soon as possible (my dad has the camera and is at work :p )

Ok I'm back with some pictures... Don't concentrate on my bad handiwork, just get an idea of what it should/can look like.;)

http://www.imagestation.com/picture/...f/fb54d636.jpg

http://www.imagestation.com/picture/...d/fb54d632.jpg

http://www.imagestation.com/picture/...d/fb54d634.jpg

http://www.imagestation.com/picture/...a/fb54d621.jpg

http://www.imagestation.com/picture/...7/fb54d624.jpg

It takes up 2 PCI slots but as you can see, I don't even have 1 CPI card... so it's no problem for me. You can get low profile 1U heatsinks that should'n't even take up 1 slot if you really need all 5. :p

Enjoy! I'd be glad to take any questions/comments.:D

EDIT: Pics working now?

pictures dont seem to link
says sorry ou are trying to access and image from outside of imagestation.com

even when i tried to use direct link didnt seem to work

Awww crap...literally.;) I'll edit them.:)

Pics work. Chuck give us the pre-mod and post mod OC's please.

Ok I can give you the pre-mod o/cs.

374/339

As for after the mod, so far I've only bumped up the core as I can't really see the RAM improving and I've done 396 totally fine. (at least in 3DMark:p ) Haven't tried higher yet. I'm going out with a few buds so I'll try to get some work done when I get back.:D

19K here I come!;)

So wait your homebrew copper ramsinks had no effect? I double checked and you said you were at 330 before the ramsinks. BTW, I saw the same copper pipe ends at Lowe's. They come individually or in a ten-pack for $1.40USD. Even if I net only 10Mhz extra like you did that's only just fine for the price. I figure I could use 8 on my 4200 and 2 on my Southbridge, maybe.

330-339...;)

I agree. It's not gonna hurt and costs next to nothing, so I just went ahead with it and tried.

Ok, I'm at 400 now... :D

i would do that with my old volcano7 but it would hit the bottom of the case:D but that is a cool idea:D
I've got a copper heatsink i wonder if it would cool it better than aluminum but with a 60mm fan running on a rheostat

Well, one thing I forgot to mention. I did the mod to make the stock fan spin at ~3600RPMs instead of the normal ~2600RPMs. Then fan I measured is 70mm. As long as you have good airflow through the heatsink, you should have better results than me since copper absorbs heat faster, but retains it longer, so blow the heat away and you should have a winner.:D

Hi:

Why no use nylon screws and nuts? No worry about shorts.

Gary

Wow thats a kick *** mod. I always thought thats the fan even aftermarket ones were to small for the GPU. Mine always is hot as hell with the stock GPU and ram heatsinks. Now that I got my SLK 900 I might have to try this mod out myself. Good Stuff

Quote:

---

Originally posted by sgtgto
Hi:

Why no use nylon screws and nuts? No worry about shorts.

Gary

---

Hmmm... Guess I didn't think of this and I also didn't see them... I saw some plastic screws and nuts, but they were all too big.

Quote:

---

Originally posted by Zy
Wow thats a kick *** mod. I always thought thats the fan even aftermarket ones were to small for the GPU. Mine always is hot as hell with the stock GPU and ram heatsinks. Now that I got my SLK 900 I might have to try this mod out myself. Good Stuff

---

Yeah, the stock thing is a POS even compared to this P4 stock heatsink. Just larger area and a larger fan to cool it.

I'd be hesitant to try it with a SLK-900U. Firstly and most importantly, my heatsink and fan probably weighs ~250-300g. The SLK-900U alone is pushing 600g. Then add a 50-100g fan adn that could be too much for the AGP slot and retention bracket to hold. I wouldn't want to see a card rip off the mobo half way through playing a game or something.

Second, if it weren't too heavy, that's a pretty expensive piece of equipment. My heatsink was free and I said, hey, no loss if I totally pulverize it in my attempts. I know it'd suck if I destroyed a 900U though.

Just a few thoughts.;) :)

My card is now super heavy but its holding nicely. The nine total cooper caps I added added over 1 pound to the cards weight but its secure

Hmm.. that's probably true, but just looking at the SLK-900U and then the video card makes my legs shake..;) :D

If you got the retention clip in place though think how hard you'd have to pull for that to come undone. Please no one actually pull your card out with the clip on I'm quite sure its way more than a couple pounds of force.

Man seeing this makes me angry about buying a zalman heatpipe, even though I got it for cheap, it blocks two ram chips so I can't put heatsinks on them. I bet the cooling upgrade it about the same (with a fan blowing on the zalman).

Is a p4 heatsink bigger than an athlon barton heatsink?

pc

I believe it is. I think the stock Barton heatsinks at 60x60mm base right? If so, you don't even need to do cutting cause 60x60 is what I had to cut mine down to so that it fit.