Search Results - Sharky Forums

Sharky Forums


Search:

Type: Posts; User: Fred E. Krugar

Page 1 of 19 1 2 3 4

Search: Search took 0.13 seconds.

  1. Just go to www.Asus.com. Look for the board you...

    Just go to www.Asus.com. Look for the board you are refering to and it will tell ya all the specs:)
  2. Tekime he was asking Royal Oaks:)

    Tekime he was asking Royal Oaks:)
  3. Replies
    15
    Views
    924

    I just Flashed my Bios to the 1003 and it gave me...

    I just Flashed my Bios to the 1003 and it gave me 230Mhz also it gives support for the new 800mhz FSB CPU.


    The Agp/Pci Lock is fixed too
  4. Replies
    9
    Views
    693

    Thanks for all the replies:cool: :cool: :cool: ...

    Thanks for all the replies:cool: :cool: :cool:


    I just put some of the Mushkin on order:D
  5. Replies
    9
    Views
    693

    Thanks for the info Royal:)

    Thanks for the info Royal:)
  6. Replies
    9
    Views
    693

    Royal do ya know what voltages i can safely run...

    Royal do ya know what voltages i can safely run that Muskin????


    Plz say atleast 2.8 :D :D :D


    Also where might i find the TwinMos???
  7. Replies
    9
    Views
    693

    Muskin Ram.....Worth A $#!&??????

    Well is it any good???? Somebody tell me it is ok :) It is PC3500 do any of yall think it will run as advertised (Speed Settings)????


    Thx for any replies:cool: :cool: :cool:
  8. Thanks Doc:cool: :cool: :cool: So there...

    Thanks Doc:cool: :cool: :cool:



    So there is no way i can connect to the front panel .the front panel has all the wires and stuff routed i just dont have anywhere to connect them to lol
  9. SB Live Gurus...Is there such a thing???

    Ok i have the SB live card and was wanting to know what were all the open pins on the underside of the card were for.....


    Also is there any way that i could connect my front panel audio...
  10. Replies
    1
    Views
    191

    Well socket 478 is just your normal P4. Also...

    Well socket 478 is just your normal P4.

    Also the 3.0 800 will work you just wont get the full use of it.

    yall correct me if i am wrong.
  11. Replies
    4
    Views
    519

    I have the 7+ but what i did was take the yellow...

    I have the 7+ but what i did was take the yellow wire out of its connector and just put it in the 3 pin connector that is attached directly to the fan.
  12. Replies
    4
    Views
    519

    well so far it has been working fine and it steps...

    well so far it has been working fine and it steps the RPMs down to 4100 from 6000. Is that good or does the switch lower it more than 4100 ????
  13. Replies
    22
    Views
    1,096

    Well lets all just put this in a different...

    Well lets all just put this in a different light...In my opinion AMD will always be here.(I am nowhere near a AMD fan)

    Look at it this way remember back in the mid 70's when chrysler was about...
  14. Replies
    0
    Views
    150

    P4 2.4b Temps

    What kinda Temps you guys getting on these CPU at stock speeds at Idle???

    I would like an idea of what i should be looking at before i start overclocking

    Thx
  15. Replies
    9
    Views
    311

    Re: P4 Heat issue?

    well that maybe the culprit hmmmmmmm.....Thats the major change that is doing it
Results 1 to 15 of 272
Page 1 of 19 1 2 3 4