My 800D Build

[Timman_24]

CPU block is here. Time to get down to business.

[simsim44]

Good for you ,take pix

[Timman_24]

IT's alive!

No pics yet, I'm just testing it right now. However, initial runs on temp are sweet.

5C drop on the CPU compared to H60 at idle and a massive 28C drop at idle on the GPU CPU is within 4C of ambiant temp at idle. Very impressive so far. Can't wait to run kombuster.

EDIT: Holy hell, 55C drop on load with the GPU.

[simsim44]

sweet !

[Timman_24]

I buttoned it up and finally have some pictures. After putting it all together, there are definitely some things I want to change around and add.

I need to back-light the reservoir because the UV coolant doesn't pick up light nearly as much as I wanted it to. I may experiment with UV LEDs or simply get blue ones like I did with the pump. I may also switch out the tubing with UV blue tubing and just run distilled water with antibacterial drops.

I also want to add another fan controller, rewire some things because I ran out of sleeving material, and finish running my temperature sensors. I may also add some new fittings that are 45 degrees when I change out the tubing.

Anyway, on the with pics:











I need a blue motherboard! I also want to resleeve my 24Pin ATX motherboard cable. It sticks out like a sore thumb.

[James]

Asus or Gigabyte for a blue motherboard.

Damn, that's sweet man. Looks awesome, and sounds like it is working awesome!

Reminds me why I watercooled for so long. The GPU temps were always the ones that made it worth it.

[simsim44]

well done Looks great

[Timman_24]

I'll swap out the motherboard and ram when Ivy is released.

I think I'm going to get some sticker paper and make a new label for the PSU

[Timman_24]

Here's a mock up of the label:



Here's the label up close:

[Timman_24]

I got the 470 up to 880mhz on the core without a crash yet. Temps are stable at 40C. The 470 is a pretty damn powerful card when properly cooled. I'm easily hitting 570 performance in Furmark. Stock clock is 600mhz, so a 280mhz overclock is ridiculous! I want to hit around 900 stable. That would start edging me into 580gx range!

My 3DMark11 score went from P4800 to P6300. Average range for 580GTX with my processor is P6500-P7300!

Adding this waterblock gave me the performance of a 400+ dollar card, but my temps are 40C lower than it

[Timman_24]

Volt modded the bios and was able to hit 900mhz, Furmark stable. I'm going to try for a bit higher tomorrow. I'll play games at 880mhz.

[simsim44]

Hows the drive face plate coming?

[Timman_24]

Hows the drive face plate coming?

Haven't had time, although I did purchase some mini wood clamps to hold the drive face. I could probably mess around with it soon and have something to show.

[flutie98]

Timman,

Looks great dude! Water on a GPU is such a massive decrease in temps aint it?

Suggestion, the drain line looks out of place, if you swapped it to the bottom position of the res the tubing would look less abrupt. Not sure if that config is possible with that res tho.

[Timman_24]

Timman,

Looks great dude! Water on a GPU is such a massive decrease in temps aint it?

Suggestion, the drain line looks out of place, if you swapped it to the bottom position of the res the tubing would look less abrupt. Not sure if that config is possible with that res tho.

It is definitely possible. The problem I ran into is needing a 45 or 90 degree fitting so the GPU line could go into the side of the res. I only have 2 holes on the bottom of the res. The pump can't connect there because there is an acrylic tube that runs to the upper part of the reservoir attached to the spot, which is a poor choice for a drain line as well lol.

I'm in the process of reworking the layout and ordering some 45/90 degree fittings for key areas as well as some new tubing. I don't care for the color of the coolant.

It looks like that blue toilet water